Cypress Semiconductor Perform CY7C1380D Spécifications Page 55
- Page / 62
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Altera Corporation A–1
May 2007
Appendix A. Restoring the
Factory Configuration
Introduction
To restore the factory configuration, you must reprogram the flash
memory on the board, and you must reprogram the EPM7256AE
configuration controller device.
Nios II Embedded Design Suite provides the files required for this
operation in the directory <Nios II EDS install path>/examples
/factory_recovery.
Reprogramming
the Flash
Memory
To reprogram the flash memory on the development board, perform the
following steps:
1. Open a Nios II command shell.
On a Windows PC, click Windows Start, point to Programs, Altera,
Nios II EDS <installed version>, and then click Nios II Command
Shell.
2. From the examples directory, change to the factory_recovery
directory for your development kit.
cd factory_recovery/niosII_stratixII_2s60_rohs
3. Run the flash-restoration script:
./restore_my_flash
4. Follow the script's instructions.
Reprogramming
the EPM7256AE
Configuration
Controller
Device
If the configuration controller design was modified, you must also
reprogram the EMP7256AE device (U3). To reprogram the EMP7256AE
configuration controller, perform the following steps:
1. Move the programming cable from J24 to J5, labeled “For U3.”
1 The orientation of J5 is opposite that of J24. When properly
connected to J5, the programming cable lies naturally over
the clock oscillator and the dual seven-segment display.
- Reference Manual 1
- Part Number MNL-01001-1.3 2
- Contents 3
- About this Manual 5
- Typographic 6
- Conventions 6
- 1. Overview 7
- Programmed 8
- Reference 8
- Overview 10
- 2. Board Components 11
- Connections & Interfaces 12
- Configuration & Reset 12
- Stratix II EP2S60 13
- Device (U60) 13
- Push-Button 14
- Switches (SW0 14
- Individual LEDs 15
- (D0 - D7) 15
- Seven-Segment 15
- LEDs (U8 & U9) 15
- SSRAM Chip 16
- Table 2–6. SSRAM Pin Table 17
- DDR SDRAM 19
- Chip (U63) 19
- Flash Memory 21
- Ethernet 23
- MAC/PHY (U4) & 23
- RJ45 Connector 23
- Serial Connector 25
- Expansion 26
- Prototype 26
- Connectors 26
- (PROTO1 & 26
- Board Components 28
- Notes to Figure 2–7: 28
- Table 2–11. PROTO1 Pin Table 29
- Notes to Figure 2–9: 31
- Table 2–12. PROTO2 Pin Table 32
- CompactFlash 33
- Connector 33
- PMC Connector 36
- (JH1 & JH2) 36
- Connector (J25) 39
- Test Points 41
- (TP1–TP8) 41
- EPCS64 Serial 42
- Configuration 42
- Device (U69) 42
- Controller 43
- Device (U3) 43
- SW8 – CPU Reset 44
- Factory 45
- Reset Distribution 46
- Starting Configuration 46
- Configuration Process 47
- Flash Memory Partitions 48
- JTAG Connectors 49
- (J24 & J5) 49
- Clock Circuitry 51
- Figure 2–21. Clock Circuitry 52
- Power-Supply 54
- Circuitry 54
- Appendix A. Restoring the 55
- Appendix B. Connecting to 57
- Connecting the LCD Screen 58
- Obtaining an IP Address 58
- LAN Connection 59
- Point–to–Point Connections 60
- Browsing to Your 61
Produits connexes et manuels pour Non Cypress Semiconductor Perform CY7C1380D
(31 pages)3b-scientific Resusci Anne CPR Torso manuály
Uživatelské manuály a uživatelské příručky pro Zdraví a hygiena 3b-scientific Resusci Anne CPR Torso.
Poskytujeme 1 manuály pdf 3b-scientific Resusci Anne CPR Torso ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels