Cypress Semiconductor Perform STK12C68 Instructions d'exploitation Page 39
- Page / 111
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
3-24 (E)
DFP-R3000
1. S side optics adjustment
n
By touching against the lens and the protection glass of the
CCD adjustment table, do not make them dirty.
Step 1. Preparation
(1) Load the alignment film into the DFP-R3000 and
projector, and then run the alignment film.
(2) Input the command C1 (press the “C” key and “1”
key) from the PC keyboard at the screen of the termi-
nal software started and then press the Enter key.
Step 2. CCD magnification and focus rough adjustment
(1) Input the command m0 from the PC and then press the
Enter key.
(2) Loosen the two hexagon cap screws as the bottom of
the optics block about a half turn.
(3) Set the sweep times of the oscilloscope so that the
pulse width (high level) of the oscilloscope CH2
output waveform is 6 DIV (scales).
(4) Rotate and adjust the fifth and sixth CCD adjustment
screws from the mechanical deck chassis using a hex
wrench driver so that amplitude A of the output
waveform of the oscilloscope CH1 becomes maxi-
mum.
(5) Check that the film data width of the oscilloscope CH1
meets the following specification.
Specification : Film data width = 6 ±0.1 scales
. When the film data width is narrower than the above
specification, turn the adjustment screw at the sixth from
the mechanical chassis counterclockwise and perform
the procedure (4) and (5) above.
. When the film data width is wider than the above
specification, turn the adjustment screw at the sixth from
the mechanical chassis clockwise and perform the
procedure (4) and (5) above.
3-5. Optics Adjustment
Optics block
Bottom side
Hex head (S side)
Adjustment screw
(S side)
Adjustment screw
(S side)
SE-437 board
(S side)
Optics block
- Film-Tech 1
- SDDS Player System 2
- ! WARNING 3
- ! WARNUNG 3
- ! AVERTISSEMENT 3
- Table of Contents 4
- 4. Spare Parts 5
- 6. Block Diagram 5
- 7. Board Layouts 5
- 8. Schematic Diagrams 5
- Manual Structure 6
- Related manuals 7
- Section 1 8
- Service Overview 8
- 1-2. Removal of Cabinet 9
- DFP-R3000 10
- 1-5. Tools 11
- Section 2 12
- /(Note 1) 14
- (Refer to the section 2-1) 14
- Section 3 16
- Required equipment 17
- Required Tools 17
- Reassembling 18
- Procedure 21
- 3-1-5. Drum assembly 24
- Sprocket 25
- 3-1-8. CCD (S and P sides) 29
- Adjustment : 31
- C1 (press the “C” key and “1” 34
- Adjustment 35
- 3-4. Film Running Checking 36
- 3-5. Optics Adjustment 38
- 3-6. FG checking 47
- 3-7. Error Rate Checking 48
- Section 4 50
- Spare Parts 50
- CHASSIS, OPTICS BLOCK 51
- 4-2. Exploded Views 51
- DRUM, LED ASSEMBLY 53
- 4-3. Electrical Parts List 57
- 4-4. Accessories Supplied 71
- Section 5 72
- Semiconductor Pin Assignments 72
- TRANSISTOR 73
- CXB1341R (SONY) 75
- CXD1171M (SONY)FLAT PACKAGE 75
- CXD1171M-TH 75
- DS1000Z-150(TE2) 76
- DS1000Z-25(TE2) 76
- LM2587SX-5.0 (NS) 76
- KL5C80A12CFP (KAWASAKI STEEL) 77
- TK11220BMCL 80
- TK11233AUTB (TOKO) 80
- TK16111MTL 80
- XRD44L60CIV (EXAR) 80
- Section 6 82
- Block Diagram 82
- RD-35 7-2 86
- SE-437 7-2 86
- SE-439 7-6 86
- TG-208 7-8 86
- RD-35 -A SIDE 87
- DUS-179 -B SIDE 87
- DUS-180 -B SIDE 87
- DUS-182 -B SIDE 87
- RD-35 -B SIDE 88
- SE-439 -A SIDE 91
- SE-439 -B SIDE 91
- TG-208 -A SIDE 93
- TG-208 -B SIDE 93
- Section 8 94
- Schematic Diagrams 94
- B-¥BCX145-RD35-1213-SM 95
- RD-35 (2/4) 96
- RD-35 (3/4) 97
- B-¥BCX145-RD35-14-SM 99
- RD-35 (2/5) 100
- RD-35 (3/5) 101
- RD-35 (4/5) 102
- RD-35 (5/5) 103
- B-¥BCX145-TG208-11-SM 104
- TG-208 (2/3) 105
- TG-208 (3/3) 106
- BOARD NO. 1-669-256-12, 13 107
- Frame Wiring 108
- Sony Corporation 1998. 8 08 111
3b-scientific Resusci Anne CPR Torso manuály
Uživatelské manuály a uživatelské příručky pro Zdraví a hygiena 3b-scientific Resusci Anne CPR Torso.
Poskytujeme 1 manuály pdf 3b-scientific Resusci Anne CPR Torso ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels